Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Carmichael?
Gate parts and welding in Carmichael typically run $95 to $450 for parts and hardware, and $150 to $650 for welding a hinge, post, frame or gate section. Small fixes like a bent hinge pin or a cracked weld on a hinge plate usually land near the low end of that range. The exact price comes down to the part, the metal, and how much labor it takes to get the gate swing or slide correctly again. We put the numbers in writing before any work starts.
That range covers the manual and automated gates people actually own here: steel and aluminum drive gates, ornamental iron garden gates, and the heavier slide gates on light commercial properties. Getting a straight, real estimate means knowing what failed. A hinge that pulled out of a post is a different job than a motor that stops halfway. Call (877) 752-3866 for a free estimate. We answer 24/7. Fast dispatch 7am-7pm, Sunday through Friday.
Gate Parts & Welding Cost Breakdown (2026)
These ranges reflect the Carmichael market heading into 2026. They are estimates for common jobs, not a fixed price list. The written estimate you get on site sets the final number.
| Line item | Estimated range |
|---|---|
| Hinge replacement (each, parts and labor) | $95 – $220 |
| Weld repair on hinge plate, frame or post bracket | $150 – $350 |
| Gate post re-set or footing repair | $300 – $650 |
| Slide gate roller and track replacement | $180 – $450 |
| Latch, striker and closer hardware | $85 – $250 |
| Gate panel straightening and re-welding | $200 – $550 |
| Operator arm or motor bracket welding | $150 – $400 |
| Full hardware refresh on a manual gate | $350 – $800 |
| New gate opening device (operator and access hardware) | $1,200 – $3,500 |
What moves a job up or down the range? The metal. Welding on galvanized steel means grinding back the coating before the weld will hold, which adds time. Welding on aluminum takes a different setup than steel, and not every shop is equipped for it. Old ornamental iron that has rusted through in places needs more prep work before a weld will stick. On the mechanical side, a hinge swap on a light garden gate is quick; a slide gate that has dropped off its track usually needs the rollers, the track and sometimes the footing addressed together. Automated gates add one more layer: when a bracket that holds the operator arm has cracked, the weld has to leave the arm at the right angle or the motor will bind every cycle.
If you’re weighing a repair against replacement, a parts-and-welding job in the low hundreds is nearly always the smaller number. A new automated gate and operator can run several thousand dollars. For a gate that’s structurally sound, welding and hardware is the cheaper path. For one with rusted-through posts and a failing operator both, replacement starts to make sense. We tell you which one your gate actually needs after we’ve seen it.
What Affects Gate Parts & Welding Pricing in Carmichael
Carmichael sits in a hot, dry-summer valley, and that shapes what fails on a gate. Long dry months, strong summer sun, and winter rains that come in a short wet stretch all take a toll on the same hardware. Here’s what drives the bill.
- Sun exposure and heat. Metal gates facing south or west through a Sacramento Valley summer get hot enough to warp light aluminum panels and cook the seals and bushings in rollers and hinges. A gate that’s warped needs straightening before new hardware will fit right, which adds labor to a parts job.
- Rust and dry-rot of the metal. The wet winter weeks plus summer irrigation lines keep gate posts and bottom rails damp at ground level. Rust eats hinge plates and the bottoms of iron gates from the inside. A weld onto thin, rusted metal won’t hold, so we cut out the bad section and weld in new stock, which costs more than a straight weld repair.
- Steel versus aluminum versus ornamental iron. Steel is the most economical to weld. Aluminum needs a different process. Cast ornamental iron can crack instead of bend, so a repair sometimes means fitting a new piece. The material sets the labor.
- Manual versus automated. Manual gate work stays in the mechanical side: hinges, latches, posts. Automated gates pull in the operator, wiring and safety sensors. A weld repair near an operator arm has to protect the electronics while the torch is out, so automated jobs take longer and cost more.
- Gate size and weight. A wide, heavy drive gate puts more load on every hinge and post. Heavy gates need heavier hardware, and a post that carries one may need re-setting rather than a simple weld.
- Brand of operator. When the failing part involves the opener – the arm bracket, the control board, the limit switch – the brand matters. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, so parts sourcing on a name-brand operator doesn’t stall the job.
You can read more about what we handle on the gate repair Carmichael page, and if you’re new to the area, our Carmichael page covers the neighborhoods and property types we see most.
How to Save on Gate Parts & Welding
There’s no secret to a lower gate bill. The savings come from catching a problem while it’s still small and from keeping the gate from working against itself.
- Fix a hinge before it rips the post. A loose or bent hinge is a $95 to $220 fix. Left alone, it pulls the post bracket out and turns into a $300 to $650 post re-set. Small early repairs are the biggest saving on this list.
- Keep the gate swinging free. A gate that drags wears out hinges, rollers and the operator faster. If it catches on the ground or needs a shove to close, get it looked at before the motor and the hardware both fail.
- Clear the track and the swing path. Dirt, leaves and gravel in a slide gate track make the motor work harder and wear the rollers. A few minutes of clearing keeps the moving parts honest.
- Ask for the repair estimate before the replacement quote. Some shops lead with replacement. Ask what a straight repair costs. On a structurally sound gate, the repair almost always wins on price.
- Get the estimate in writing. The free estimate is where the price gets fixed per job, so ask for the parts and labor breakdown before work begins. Call (877) 752-3866 to get one scheduled.
It helps to know which brand your operator is before you call. Lift the cover or look at the housing label. Having that on hand saves a step when we’re matching parts.
FAQs – Gate Parts & Welding Cost
How much does it cost to repair a gate hinge in Carmichael?
Hinge replacement in Carmichael typically costs $95 to $220 per hinge, parts and labor together. If the hinge has pulled out of the post or torn the frame, the weld repair that goes with it brings the total to $150 to $350 or more. Call (877) 752-3866 for an exact quote on your gate.
Can welding fix a bent or broken gate?
Yes, welding fixes most bent or broken steel and iron gates, usually for $150 to $550. A cracked hinge plate, a split frame or a snapped post bracket is a straightforward weld repair. If the metal is rusted thin or the gate is badly warped, the fix may need new stock cut in, which costs more. We’ll tell you which one your gate needs.
Is it cheaper to repair or replace a gate?
Repair is cheaper in most cases: a weld and parts job runs $150 to $800, while a new automated gate and operator runs $1,200 to $3,500 and up. Replacement only wins when the posts and frame are rusted through or the operator is failing alongside structural damage. For a sound gate, repair is the lower number every time.
Do you work on electric and automated gate operators?
Yes. We repair electric and automated gates alongside manual ones, and we handle the brand you already own. That includes LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. That covers the motor, control board, safety sensors and access hardware, not just the mechanical parts.
How soon can you come out to look at my gate?
We offer same-day service when the schedule allows, and we answer the phone 24/7. Fast dispatch 7am-7pm, Sunday through Friday. Call (877) 752-3866 and we’ll book you into the next opening.
We’re a gate specialist, not a general contractor, and we’ve worked on Carmichael gates since 2014. That means every job – from a broken hinge to a failed FAAC motor board – stays in the hands of people who do this and nothing else. From the motor to the hinge, we know the whole gate.
Whatever opener you have, we know it. Call (877) 752-3866 for a free estimate. We answer 24/7. Fast dispatch 7am-7pm, Sunday through Friday. Or get in touch through our Carmichael page and we’ll set up a time.
Pricing reflects the Carmichael market as of 2026. Gate Repair Carmichael offers free estimates – call (877) 752-3866.
Written by the team at Gate Repair Carmichael, serving Carmichael since 2014.
What Our Customers Say
"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Michelle Barrett"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Michelle Nguyen"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
- Oscar Castillo